Deciphering the Origins of P1-Induced Power Losses in Cu(Inx,Ga1–x)Se2 (CIGS) Modules Through Hyperspectral Luminescence

In this report, we show that hyperspectral high-resolution photoluminescence mapping is a powerful tool for the selection and optimization of the laser ablation processes used for the patterning interconnections of subcells on Cu(In_x,Ga_1−x)Se₂ (CIGS) modules. In this way, we show that in-depth monitoring of material degradation in the vicinity of the ablation region and the identification of the underlying mechanisms can be accomplished. Specifically, by analyzing the standard P1 patterning line ablated before the CIGS deposition, we reveal an anomalous emission-quenching effect that follows the edge of the molybdenum groove underneath. We further rationalize the origins of this effect by comparing the topography of the P1 edge through a scanning electron microscope (SEM) cross-section, where a reduction of the photoemission cannot be explained by a thickness variation. We also investigate the laser-induced damage on P1 patterning lines performed after the deposition of CIGS. We then document, for the first time, the existence of a short-range damaged area, which is independent of the application of an optical aperture on the laser path. Our findings pave the way for a better understanding of P1-induced power losses and introduce new insights into the improvement of current strategies for industry-relevant module interconnection schemes.     

甲基氯硅烷精馏流程的模拟与优化

采用Aspen plus软件对工业七塔精馏过程进行全流程建模与模拟，优化工艺参数，研究了新的精馏节能工艺。对一甲塔等7个精馏塔采用双因素水平的灵敏度分析，考察了塔釜采出率、回流比、进料位置和塔顶压力对产品浓度和热负荷的影响，确定一甲塔最优的工艺参数：塔釜摩尔采出率为0.92，摩尔回流比为130，塔顶压力为0.18 MPa，总理论板数为400，在210块理论板位置进料。在此基础上，针对高能耗的脱高塔/脱低塔，模拟研究了双效精馏新工艺，新工艺可节省39.70%的年总成本；针对一甲塔模拟研究了热泵精馏新工艺，新工艺可降低41.42%的年总成本。     

内插螺旋立式上行管流场及传热性能的实验研究

通过粒子图像测速流场实验与传热实验相结合，研究了内插螺旋立式上行管的螺旋节距、丝径、中径比等结构参数在不同Re下对流场、阻力及传热性能的影响。结果表明，内插螺旋能够有效扰动和混合管内流体，使管内形成多个纵向旋涡的流体结构、增大管壁附近液体涡量，有利于强化传热。当Re相同时，管内平均流速v、Nu和综合换热性能PEC均随丝径增大而增大，随中径比减小而增大；随节距增大，3种参数均出现增大的趋势，节距大于20 mm后开始减小。管内流体的阻力f随丝径和节距增大而减小，随中径比增大而增大。综合比较，在较低Re时，节距p=20 mm、丝径e=1.6 mm、中径比D/d=0.75时综合传热效果最好。     

API X52管线钢与Corus RQT 701超高强钢的焊接工艺

针对超高强钢在机械行业的广泛使用,焊接接头易出现淬硬脆化、裂纹等缺陷的情况,采用焊条电弧焊(SMAW)和药芯气体保护焊(FCAW-GS)组合的焊接方法,对API X52管线钢与Corus RQT 701超高强钢的焊接进行了工艺试验,并进行常规力学性能试验。结果表明,通过合理匹配焊接工艺参数,严格控制低热输入量及层间温度,实现了小熔合比的异种钢焊接,且焊接接头具有良好的力学性能,达到了标准和规格书的要求;异种高强钢焊接,采用SMAW打底焊接和FCAWGS填充并盖面的方法,焊接效率较单纯采用焊条电弧焊工艺提高2倍以上。     

Ethanol absorption from CO2 using solutions of glycerol and glycols

CO₂ stripping during fermentation is a possible way of increasing the production of ethanol in distilleries. Ethanol, water, and carbon dioxide are the main compounds in the exiting gas mixture. To date, few studies have proposed the use of absorption to recover ethanol from this mixture or have considered different absorbents for this purpose. This work evaluates different absorbent solutions used to recover ethanol vapor from CO₂ gas. Glycols and glycerol can provide easier separation of ethanol than water, with lower distillation energy demand. A statistical experimental design was used to compare the mass transfers of ethanol from the gas phase to the liquid phase, using solutions of glycerol, ethylene glycol, and diethylene glycol. High concentrations of these substances did not favor the absorption of ethanol. The best results were achieved with 25% absorbent solutions, which offered better options than water for the recovery of ethanol from CO₂ gas in absorption columns and could increase the productivity of first generation bioethanol production.     

两池火耦合作用下柴油拱顶罐热响应的数值模拟

化工园区多池火事故是典型的高后果低概率事件。鉴于目前两池火辐射模型存在一定局限性，本文采用数值模拟方法，以3个直线排布的5000m³柴油拱顶罐为研究场景，从热释放速率、火焰形态、热辐射强度三方面分析两池火燃烧特性，并与单池火场景对比，考虑储罐间距这一影响因素，进一步研究目标储罐热响应。结果表明：采用GB 50160—2008（2018年版）规定的防火间距，两燃烧罐产生的池火会发生耦合作用，并得出目标储罐受到的热辐射强度分布，最高热辐射达17.04kW/m²；两池火作用下目标储罐的温度、Mises应力与失效时间分别为644℃、356MPa、936s，单池火为488℃、280MPa、2880s，目标储罐在两池火作用下的变形也比单池火更为严重；随着储罐间距增加，目标储罐的温度与Mises应力逐渐减小，失效时间逐渐增加，当储罐间距为标准防火间距的2.5倍（20m）时，失效时间为2800s，与单池火作用产生的失效时间2880s较为接近。本研究可为优化储罐防火间距及区域韧性提升提供理论指导。     

[成形过程仿真优化与集成计算材料工程]限定加热管布局的快速热循环注塑成形模具电加热系统优化

针对管道布局、最大允许能耗给定条件下快速热循环注塑成形（RHCM）注塑模具型腔表面快速均匀加热的问题，提出以单根加热棒热流密度为设计变量，以模具型腔表面升温效率和温度分布均匀性为目标，结合有限元模拟、响应面设计以及多目标粒子群优化技术来优化RHCM模具电加热系统。与优化前相比，加热系统优化后，模具型腔表面最大温差降低63.4%，加热系统总能耗降低9%。对比了不同注塑成形工艺条件下成形的平板塑件表面质量，结果表明，相对传统注塑成形（CIM）工艺，RHCM工艺将制品表面粗糙度Ra从320 nm降低到118 nm，并有效抑制了制品表面熔接痕、缩痕等缺陷；发现制品表面粗糙度与型腔表面对应点温度成负相关，说明优化后的型腔表面温度分布更有利于提升制品表面质量。     

The Impingement Heat Transfer Data of Inclined Jet in Cooling Applications: A Review

On the impingement heat transfer data,the experimental studies of air and liquid jets impingement to the flat surfaces were collected and critically reviewed.The oblique impingements of both single circular and planar slot jets were considered in particular.The review focused on the surface where the jet impingement cooling technique was utilized.The nozzle exit Reynolds numbers based on the hydraulic diameter varied in the range of 1,500–52,000.The oblique angles relative to the plane surface and the dimensionless jet-to-plate spacing vary in the range of 15°–90°and 2–12 respectively.The review suggested that the magnitude of maximum heat transfer shifted more for air jets compared with the liquid jets.The drop in the inclination angle and the jet-to-plate separation led to the increase in the asymmetry of heat transfer distribution.The displacement of maximum Nusselt number(heat transfer)locations was found to be sensitive to the inclination angle and the smaller jet-to-plate distance.Also,the Nusselt number correlations proposed by various researchers were discussed and compared with the results of the cited references.